AP8130DN Access Point - Huawei Products
Under Construction!

Prompt

You have not logged in. Want to enter the login page?

Yes No

Prompt

Sorry that you are not authorized to download this document.

Apply Previous

Register an account

  • *
  • *
  • *
  • *
  • *
  • I agree that Huawei representatives may contact me.
  • I agree to receive information on Huawei products by email.
  • Terms of UsePrivacy Policy

If you already have a Huawei account, please login to download

AP8130DN Access Point

The AP8130DN, a technology-leading 802.11ac access point, is high- and low-temperature resistant, dustproof, and waterproof. It is recommended for use in coverage scenarios (squares, pedestrian streets, and amusement parks) and bridging scenarios (wireless harbors, data backhaul, video surveillance, and train-to-ground backhaul).
•3x3 MIMO (three spatial streams)
•Maximum rate: 1.75 Gbit/s
•IP67
•Built-in surge protection
•23 dBm


Appearance

Ports

1.GE0/PoE interface: a 10/100/1000M interface, which connects to the wired Ethernet and supports the PoE power supply.


2.GE1 interface: a 10/100/1000M interface, which connects to the wired Ethernet.


3.SFP: an optical interface.


4.5 GHz antenna interface.


5.2.4 GHz or 5 GHz antenna interface.


6.Console interface.


7.RSSI: used to obtain the transmit power through measurement of its pin voltage.


8.Default button: restores the factory settings if you remove the screw and hold down the button more than 3s from the hole.


LED Indicators

Type Color Status Description
Default status after power-on Green Steady on The AP is just powered on and the software is not started yet.
Software startup status Green Steady on after blinking once After the system is reset and starts uploading the software, the indicator blinks green once. Until the software is uploaded and started, the indicator remains steady green.
Running status Green Blinking once every 2s (0.5 Hz) The system is running properly, the Ethernet connection is normal, and STAs are associated with the AP. The system enters the Uboot CLI.
Blinking once every 5s (0.2 Hz) The system is running properly, the Ethernet connection is normal, and no STA is associated with the AP. The system is in low power consumption state.
Alarm Green Blinking once every 0.25s (4 Hz) The software is being upgraded. After the software is uploaded and started, the AP working in Fit AP mode requests to go online on the AC and maintains this state until it goes online successfully on the AC (before the CAPWAP link is established). The AP working in Fit AP mode fails to go online on the AC (the CAPWAP link disconnects).
Fault Red Steady on A fault that affects services has occurred, such as a DRAM detection failure or system software loading failure. The fault cannot be automatically rectified and must be rectified manually.

Descriptions about the Link indicator


Type Color Status Description
LINK Green Steady on The system is running properly, the Ethernet connection is normal, and no data is being transmitted.
ACT Green Blinking The system is running properly, the Ethernet connection is normal, and the AP is transmitting data. The indicator blinks more quickly when more data is being transmitted.

Description about the Wireless indicator (Traffic volume indicator)


Color Status Description
Yellow/green Off Radios are disabled, and no STA is connected to the AP.
Yellow/green Steady on The AP has STAs connected to the 2.4 GHz radio or 5 GHz radio, but no data is being transmitted.
Green Blinking The AP has STAs connected to the 2.4 GHz radio and is transmitting data. The indicator blinks more quickly when more data is being transmitted.
Yellow Blinking The AP has STAs connected to the 5 GHz radio and is transmitting data. The indicator blinks more quickly when more data is being transmitted.
Yellow/green Blinking alternatively The AP has STAs connected to both the 2.4 GHz radio and 5 GHz radio. The indicator blinks more quickly when more data is being transmitted.

Description about the Wireless indicator (Wireless bridge indicator)


Color Status Description
Yellow/green Off The AP is not transmitting or receiving data or the signal strength is extremely low.
Steady on The AP is transmitting or receiving data normally, and the signal strength is high.
Blinking green once every 0.25 seconds (4 Hz) The AP is transmitting or receiving data normally, and the signal strength is medium.
Blinking once every 2s (0.5 Hz) The AP is transmitting or receiving data normally, and the signal strength is low.

Highly reliable wireless access

  • Complies with IEEE 802.11a/b/g/n/ac.
  • Supports 3x3 MIMO and a maximum rate of 1.75 Gbit/s.
  • Supports Wi-Fi Multimedia (WMM) and priority mapping on the air interface and wired interface.
  • Supports wired link integrity check.
  • Provides two GE auto-sensing uplink electrical ports and supports PoE power supply.
  • Supports load balancing.
  • Supports roaming without service interruption.
  • Supports AC dual-link backup.
  • Supports 11n Beamforming.
  • Uses the latest 802.11ac chip to provide higher performance and wider coverage.
  • Uses a metal shell and heat dissipation design to ensure high reliability.
  • Supports airtime scheduling which ensures fairness in channel occupation time for all users.


Comprehensive user access control capability

  • Supports access control lists (ACLs) and implements user access control based on the user group policy.
  • Provides fine-grained bandwidth management for each user.
  • Supports user isolation policies.
  • Supports unified authentication on the AC.
  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address, user agent (UA) information in an HTTP packet, and DHCP options.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.


High security

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2/WPA-WPA2-PSK authentication and encryption
  • WPA/WPA2/WPA-WPA2-802.1x authentication and encryption
  • TKIP and CCMP encryption for WPA/WPA2/WPA-WPA2: the CCMP uses a 128-bit AES algorithm to encrypt data and has a high security level.
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.


Flexible networking and environment adaptability

  • Provides flexible networking capabilities, applies to various application scenarios, and supports Mesh and WDS.
  • Has strong environment adaptability. The AP can automatically select the transmission rates, channels, and transmit power to adapt to various radio environments and avoid interference in real time.
  • Adjusts bandwidth allocation based on the user quantity and environment to improve user experience.
  • Supports the MIMO antenna system and connects to external dual-band antennas (2.4 GHz and 5 GHz). The antennas can be flexibly adjusted.
  • Identifies interference sources such as baby monitors, Bluetooth devices, digital cordless phones (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz frequency bands), wireless game controllers, and microwaves and works with eSight to locate interference sources and display spectrums.


Simple device management and maintenance

  • Automatically goes online and loads the configuration, and supports plug-and-play (PnP).
  • Supports batch upgrade.
  • Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location.
  • Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology.


High reliability and protection level

  • Provides strong hardware protection capability.
  • Adapts to a wide temperate range from -40°C to +60°C.
  • Uses industry-standard components and design methods, improving industry-level reliability.
  • Provides IP65/IP66/IP67 protection level.
  • Has a built-in 5 kA feeder surge protector and requires no external surge protective devices, which simplifies installation and lowers costs.
  • Provides 6 kA or 6 kV surge protection capability on an Ethernet interface.
  • Complies with international standards and China safety standards III.

WLAN features

  • Complies with IEEE 802.11a/b/g/n/ac and passed the certification of Wi-Fi Alliance.
  • Supports 3x3 MIMO and a maximum rate of 1.75 Gbit/s.
  • Maximum ratio combining (MRC)
  • Space Time Block Code (STBC)
  • Supports 11n Beamforming.
  • Low-density Parity-check (LDPC)
  • Maximum-likelihood detection (MLD)
  • Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only)
  • Supports 802.11 dynamic frequency selection (DFS).
  • Short GI in 20 MHz, 40 MHz and 80 MHz modes
  • Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding
  • Automatic and manual rate adjustment (the rate is adjusted automatically by default)
  • WLAN channel management and channel rate adjustment
  • Automatic channel scanning and interference avoidance
  • Service set identifier (SSID) hiding
  • Signal sustain technology (SST)
  • Unscheduled automatic power save delivery (U-APSD)
  • Control and Provisioning of Wireless Access Points (CAPWAP)
  • Automatic login
  • Wireless distribution system (WDS)
  • Mesh networking
  • Multi-user CAC


Network features

  • Compliance with IEEE 802.3u
  • Auto-negotiation of the rate and duplex mode and automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X)
  • SSID-based VLAN assignment
  • VLAN trunk on uplink Ethernet ports
  • 4094 VLAN IDs (1-4094) and a maximum of 16 virtual APs (VAPs) for each radio
  • AP control channel in tagged and untagged mode
  • DHCP client, obtaining IP addresses through DHCP
  • Tunnel data forwarding and direct data forwarding
  • STA isolation in the same VLAN
  • Access control lists (ACLs)
  • Link Layer Discovery Protocol (LLDP)
  • Uninterrupted service forwarding upon CAPWAP channel disconnection
  • Unified authentication on the AC
  • AC dual-link backup
  • Native IPv6
  • IPv4/IPv6 dual stack
  • IPv6 Portal
  • IPv6 SAVI
  • IPv4/IPv6 ACL


QoS features

  • Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding
  • WMM parameter management for each radio
  • WMM power saving
  • Priority mapping for upstream packets and flow-based mapping for downstream packets
  • Queue mapping and scheduling
  • User-based bandwidth limiting
  • Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience)
  • Airtime scheduling


Security features

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2-PSK authentication and encryption
  • WPA/WPA2-802.1x authentication and encryption
  • WPA-WPA2 hybrid authentication
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.
  • 802.1x authentication, MAC address authentication, and Portal authentication
  • DHCP Snooping
  • DAI(Dynamic ARP Inspection)
  • IPSG(IP Source Guard)


Maintenance features

  • Unified management and maintenance on the AC
  • Automatic login and configuration loading, and plug-and-play (PnP)
  • WDS zero-configuration deployment
  • Mesh network zero-configuration deployment
  • Batch upgrade
  • Local AP management through the serial interface or using Telnet
  • Real-time configuration monitoring and fast fault location using the NMS
  • System status alarm
  • Dying Gasp


BYOD

  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address.
  • Identifies the device type according to the user agent (UA) information in an HTTP packet.
  • Identifies the device type according to DHCP options.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.


Locating Service

  • Locates tags manufactured by AeroScout or Ekahau.
  • Locates Wi-Fi terminals.
  • Works with eSight to locate rogue devices.


Spectrum Analysis

  • Identifies interference sources such as baby monitors, Bluetooth devices, digital cordless phones (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz frequency bands), wireless game controllers, and microwaves.

Specifications

Item Description
Technical specifications Dimensions (H x W x D) 100 mm x 260 mm x 290 mm
Weight 2.65 kg
System memory 256 MB DDR3
64 MB flash memory
Power specifications Power input PoE power: -48 V DC
AP8130DN: PoE function in compliance with IEEE 802.3at
The AP does not support AC power supply. If AC power supply is required, use a PoE adapter. Ensure that the installation position of the PoE adapter meets requirements.
Maximum power consumption 25.5 W
Environment specifications Operating temperature -40°C to +60°C
Storage temperature -40°C to +70°C
Operating humidity 0% to 100% (non-condensing)
Waterproof grade IP65/IP66/IP67
Altitude -60 m to 4000 m


Radio Specifications

Item Description
Antenna type Outdoor external antenna
Maximum number of concurrent users ≤256
Maximum transmit power for each radio 2.4 GHz: 23 dBm
5 GHz: 21dBm
Channel rate 802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbit/s
802.11b: 1, 2, 5.5, and 11 Mbit/s
802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbit/s
802.11n: 6.5 to 450 Mbit/s
802.11ac: 6.5 to 1300 Mbit/s
Receiver sensitivity 2.4 GHz
802.11b (CCK)
-96 dBm @ 1 Mb/s
-89 dBm @ 11 Mb/s
2.4 GHz
802.11g (non-HT20)
-87 dBm @ 6 Mb/s
-74 dBm @ 54 Mb/s
2.4 GHz
802.11n (HT20)
-87 dBm @ MCS0/8
-71 dBm @ MCS7/15
2.4 GHz
802.11n(HT40)
-84 dBm @ MCS0/8
-68 dBm @ MCS7/15
5 GHz
802.11a (non-HT20)
-90 dBm @ 6 Mb/s
-73 dBm @ 54 Mb/s
5 GHz
802.11n (HT20)
-84 dBm @ MCS0/8
-70 dBm @ MCS7/15
5 GHz
802.11n (HT40)
-86 dBm @ MCS0/8
-64 dBm @ MCS7/15
-
5 GHz
802.11ac (VTH20)
-88 dBm @ MCS0NSS1
-65 dBm @ MCS8NSS1
5 GHz
802.11ac (VTH40)
-85 dBm @ MCS0NSS1
-60 dBm @ MCS9NSS1
5 GHz
802.11ac (VTH80)
-82 dBm @ MCS0NSS1
-57 dBm @ MCS9NSS1
-

Huawei AP8130DNs comply with IP67 dustproof and waterproof protection standards, applicable to coverage scenarios (for example, squares, pedestrian streets, and amusement parks) and bridging scenarios (for example, wireless harbors, data backhaul, video surveillance, and train-to-ground backhaul).


Fit AP networking (AP mode):

In this networking, the AP functions as a fit AP and provides only data forwarding functions. The AC is responsible for user access, AP go-online, AP management, authentication, routing, security, and QoS.



Fit AP networking (WDS mode: point-to-point):


Fit AP networking (WDS mode: point-to-multipoint):

In this networking, the AP connects two or more independently wired or wireless LANs through wireless links to construct a network on which users can exchange data. In Wireless Distribution System (WDS) mode, the AP supports point-to-point (P2P) and point-to-multipoint (P2MP) networking modes. With 5 GHz and 2.4 GHz frequency bands, the AP can implement wireless bridging and access functions.



Fit AP mesh networking:

On the preceding network, APs function as mesh points (MPs) and are fully-meshed to establish an auto-configured and self-healing wireless mesh network (WMN). APs with the gateway function can work as the mesh portal points (MPPs) through which the WMN can provide access to the Internet. Terminals connect to APs to access the WMN. The WMN uses dedicated mesh routing protocols to guarantee high transmission quality and is more applicable to scenarios that require high bandwidth and highly stable Internet connections.



Fat AP networking:

On the preceding network, the device functions as a Fat AP to implement functions such as user access, authentication, data security, service forwarding, and QoS.


Technology Topics


Related Products

Case Studies

DOCUMENTATION CENTER NEWS ROOM CASE STUDIES VIDEO ZONE PUBLICATIONS SHARE