AP6310SN-GN Access Point - Huawei Products
Under Construction!

Prompt

You have not logged in. Want to enter the login page?

Yes No

Prompt

Sorry that you are not authorized to download this document.

Apply Previous

Register an account

  • *
  • *
  • *
  • *
  • *
  • I agree that Huawei representatives may contact me.
  • I agree to receive information on Huawei products by email.
  • Terms of UsePrivacy Policy

If you already have a Huawei account, please login to download

AP6310SN-GN Access Point

The AP6310SN-GN is an enhanced series indoor single-band Access Point (AP), which supports indoor distributed coverage. The AP6310SN-GN can be used together with the 2G/3G/CATV Signal System, and they share the 2G/3G/CATV indoor distributed system. The AP6310SN-GN is applicable to the indoor wide coverage scenario with signal attenuation and low user density.

Appearance

Ports

1.Console interface.


2.ETH/PoE interface: a 10/100/1000M interface, which connects to the wired Ethernet and supports the PoE power supply.


3.Default button: restores factory settings if you hold down the button more than 3s.


4.Power input interface: 12 V DC.


5.Ground point: connects to a ground cable.


6.N-type radio connector interface.


LED Indicators

Information Type SYS Link Wireless Description
Startup status Steady green The system is being initialized.
Blinking green Memory check, software system, and system initialization are all normal.
Steady red Memory check fails or the system software fails to be loaded.
Running and connection status Blinking green once every 2s (0.5 Hz) Off Off The system is running properly, but no Ethernet connection is available. Radios are disabled, and no STA is connected to the AP.
Blinking green once every 2s (0.5 Hz) Off Blinking green The system is running properly, but no Ethernet connection is available. The AP has STAs connected and is transmitting data. The indicator blinks more quickly when more data is being transmitted.
Blinking green once every 2s (0.5 Hz) Steady or blinking green Off The system is running properly and the Ethernet connection is normal. Radios are disabled, and no STA is connected to the AP. The indicator blinks more quickly when more data is being transmitted.
Blinking green once every 2s (0.5 Hz) Steady or blinking green Blinking green The system is running properly and the Ethernet connection is normal. The AP has STAs connected and is transmitting data. The indicator blinks more quickly when more data is being transmitted.

Highly reliable wireless access

  • Complies with IEEE 802.11b/g/n.
  • Provides a maximum rate of 150 Mbit/s.
  • Supports Wi-Fi Multimedia (WMM) and priority mapping on the air interface and wired interface.
  • Supports wired link integrity check.
  • Supports load balancing.
  • Supports roaming without service interruption in Fit AP mode.
  • Supports AC dual-link backup and VRRP hot backup in Fit AP mode.
  • Uses the latest 802.11n chip to provide higher performance and wider coverage.
  • Uses a metal shell and heat dissipation design to ensure high reliability.


Comprehensive user access control capability

  • Supports access control lists (ACLs) and implements user access control based on the user group policy.
  • Provides fine-grained bandwidth management for each user.
  • Supports user isolation policies.
  • Supports unified authentication on the AC in Fit AP mode.
  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address, user agent (UA) information in an HTTP packet, and DHCP options in Fit AP mode.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets in Fit AP mode.


High security

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2-PSK authentication and encryption
  • WPA/WPA2-802.1x authentication and encryption
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.


Flexible networking and environment adaptability

  • Provides flexible networking capabilities and works in AP mode.
  • Has strong environment adaptability. The AP can automatically select the transmission rates, channels, and transmit power to adapt to various radio environments and avoid interference in real time.
  • Adjusts bandwidth allocation based on the user quantity and environment to improve user experience.
  • Identifies interference sources such as bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors in Fit AP mode and works with eSight to locate interference sources and display spectrums.


Simple device management and maintenance

  • Automatically goes online and loads the configuration, and supports plug-and-play (PnP) in Fit AP mode.
  • Supports batch upgrade.
  • Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location.
  • Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology.

WLAN features

  • AP6310SN-GN: complies with IEEE 802.11b/g/n.
  • AP6310SN-GN: provides a maximum rate of 150 Mbit/s.
  • Maximum ratio combining (MRC)
  • Maximum-likelihood detection (MLD)
  • Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only)
  • Short GI in 20 MHz and 40 MHz modes
  • Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding
  • Automatic and manual rate adjustment (the rate is adjusted automatically by default)
  • WLAN channel management and channel rate adjustment
  • Automatic channel scanning and interference avoidance
  • Service set identifier (SSID) hiding
  • Signal sustain technology (SST)
  • Unscheduled automatic power save delivery (U-APSD)
  • Control and Provisioning of Wireless Access Points (CAPWAP) in Fit AP mode
  • Automatic login in Fit AP mode


Network features

  • Compliance with IEEE 802.3u
  • Auto-negotiation of the rate and duplex mode and automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X)
  • SSID-based VLAN assignment
  • VLAN trunk on uplink Ethernet ports
  • 4094 VLAN IDs (1-4094) and a maximum of 16 virtual APs (VAPs) for each radio
  • AP control channel in tagged and untagged mode
  • DHCP client, obtaining IP addresses through DHCP
  • Tunnel data forwarding and direct data forwarding
  • STA isolation in the same VLAN
  • Access control lists (ACLs)
  • Link Layer Discovery Protocol (LLDP)
  • Uninterrupted service forwarding upon CAPWAP channel disconnection in Fit AP mode
  • Unified authentication on the AC in Fit AP mode
  • AC dual-link backup and VRRP hot backup in Fit AP mode
  • Native IPv6
  • IPv4/IPv6 dual stack
  • IPv6 Portal
  • IPv6 SAVI
  • IPv4/IPv6 ACL


QoS features

  • Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding
  • WMM parameter management for each radio
  • WMM power saving
  • Priority mapping for upstream packets and flow-based mapping for downstream packets
  • Queue mapping and scheduling
  • User-based bandwidth limiting
  • Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience)


Security features

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2-PSK authentication and encryption
  • WPA/WPA2-802.1x authentication and encryption
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.
  • DHCP Snooping
  • DAI(Dynamic ARP Inspection)
  • IPSG(IP Source Guard)


Maintenance features

  • Unified management and maintenance on the AC in Fit AP mode
  • Automatic login and configuration loading, and plug-and-play (PnP) in Fit AP mode
  • Batch upgrade
  • Local AP management through the serial interface or using Telnet
  • Real-time configuration monitoring and fast fault location using the NMS
  • System status alarm
  • Dying Gasp


BYOD

  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address.
  • Identifies the device type according to the user agent (UA) information in an HTTP packet.
  • Identifies the device type according to DHCP options.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.


Spectrum Analysis

  • Identifies interference sources such as bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors.
  • Works with eSight to locate and perform spectrum analysis on interference sources.

Specifications

Item Description
Technical specifications Dimensions (H×W×D) 35 mm×130 mm×150 mm
Weight 0.6 kg
System memory 128 MB DDR2
32 MB flash memory
Power specifications Power input DC 12V±10%
POE Power: -48V DC
PoE function in compliance with IEEE 802.3af and 802.3at
Maximum power consumption 8.3 W
NOTE:The maximum power consumption depends on local laws.
Environment parameters Operating temperature -10℃ to +50℃
Storage temperature -40℃ to +70℃
Humidity 5% to 95% (non-condensing)
Waterproof grade IP31
Altitude –60 m to 4000 m

Radio Specifications

Item Description
Radio connector type N type (Female)
Antenna type depends on the type of antennas in the indoor antennas system.
Maximum number of concurrent users 128
Maximum transmit power 27 dBm You can adjust the transmit power from the maximum transmit power by 20 dB, with a step of 1 dB.
NOTE:Actual transmit power depends on local laws and regulations.
Maximum number of non-overlapping channels 802.11b/g
20MHz: 3
802.11n
20MHz: 3
40MHz: 1
NOTE:The number of non-overlapping channels allowed varies in different countries. For details, see the Country codes & Channels compliance status
Channel Rate 802.11b: 1, 2, 5.5, and 11 Mbit/s
802.11g: 6, 9, 12, 18, 24, 36, 48, and 54 Mbit/s
802.11n data rate (2.4 GHz)
GI2=800ns GI=400ns
20 MHz (Mbit/s) 40 MHz (Mbit/s) 20 MHz (Mbit/s) 40 MHz (Mbit/s)
6.5 @ MCS10 13.5 @ MCS0 7.2 @ MCS0 15 @ MCS0
13 @ MCS1 27 @ MCS1 14.4 @ MCS1 30 @ MCS1
19.5 @ MCS2 40.5 @ MCS2 21.7 @ MCS2 45 @ MCS2
26 @ MCS3 54 @ MCS3 28.9 @ MCS3 60 @ MCS3
39 @ MCS4 81 @ MCS4 43.3 @ MCS4 90 @ MCS4
52 @ MCS5 108 @ MCS5 57.8 @ MCS5 120 @ MCS5
58.5 @ MCS6 121.5 @ MCS6 65 @ MCS6 135 @ MCS6
65 @ MCS7 135 @ MCS7 72.2 @ MCS7 150 @ MCS7
NOTE:Modulation coding scheme (MCS) index: determines the spatial flow quantity, modulation, coding rate, and data rate.
Guard interval (GI): indicates the period in nanoseconds the radio listens between packets.
Receiver Sensitivity 802.11b (CCK):
-97 dBm @ 1 Mbit/s
-92 dBm @ 2 Mbit/s
-92 dBm @ 5.5 Mbit/s
-90 dBm @ 11 Mbit/s
802.11g (non-HT20):
-92 dBm @ 6 Mbit/s
-91 dBm @ 9 Mbit/s
-90 dBm @ 12 Mbit/s
-87 dBm @ 18 Mbit/s
-83 dBm @ 24 Mbit/s
-80 dBm @ 36 Mbit/s
-76 dBm @ 48 Mbit/s
-74 dBm @ 54 Mbit/s
802.11n(HT20):
-92 dBm @ MCS0/8
-89 dBm @ MCS1/9
-86 dBm @ MCS2/10
-82 dBm @ MCS3/11
-79 dBm @ MCS4/12
-74 dBm @ MCS5/13
-73 dBm @ MCS6/14
-71 dBm @ MCS7/15
802.11n(HT40):
-89 dBm @ MCS0/8
-86 dBm @ MCS1/9
-83 dBm @ MCS2/10
-79 dBm @ MCS3/11
-76 dBm @ MCS4/12
-72 dBm @ MCS5/13
-70 dBm @ MCS6/14
-68 dBm @ MCS7/15

The AP6310SN-GN is recommended on large-scale networks where users are distributed in a large area and an indoor distribution system is used, for example, office buildings, business buildings, hotels, airports, and bus stations. The AP6310SN-GN APs provide indoor wireless signal coverage in these scenarios.


Fit AP networking:

In this networking, the AP6310SN-GN functions as a Fit AP that provides only data forwarding functions. The AC is responsible for user access, authentication, AP management, and configurations of security protocols, routing, and QoS.


Technology Topics


Case Studies

DOCUMENTATION CENTER NEWS ROOM CASE STUDIES VIDEO ZONE PUBLICATIONS SHARE