AP2010DN Wall Plate Access Point - Huawei Products
Under Construction!

Prompt

You have not logged in. Want to enter the login page?

Yes No

Prompt

Sorry that you are not authorized to download this document.

Apply Previous

Register an account

  • *
  • *
  • *
  • *
  • *
  • I agree that Huawei representatives may contact me.
  • I agree to receive information on Huawei products by email.
  • Terms of UsePrivacy Policy

If you already have a Huawei account, please login to download

AP2010DN Wall Plate Access Point

Enterprise-level wall plate AP2010DN uses an 86 mm plate and can be easily installed in an 86-type box. It supports the 2.4 GHz or 5 GHz frequency band, and can flexibly switch between the two frequency bands. Huawei AP2010DN provides wired and wireless connections as well as phone connections, applicable to hotels, apartments, and office buildings.
• 2×2MIMO(two spatial streams)
• FIT AP
• PoE power
• Built-in antennas

This document describes the wall plate AP2010DN, including its appearance, ports, and indicators:


Appearance

Ports


1. ETH0/ETH1: 10/100 Mbit/s interface, connects to the wired Ethernet.


2. Phone: Phone interface, connects to a traditional PSTN.


3. GE/PoE: 10/100/1000 Mbit/s interface, connects to the wired Ethernet. The interface can connect to a PoE power supply to provide power for APs.


4. Phone: Phone interface, connects to a POTS phone or modem device.


5. Default: Reset button, restores factory settings and restarts the AP if you hold down the button more than 3 seconds.



LED Indicators

Type Color Status Description
Default status after power-on Green Steady on The AP is just powered on and the software is not started yet.
Software startup status Green Steady on after blinking once After the system is reset and starts uploading the software, the indicator blinks green once. Until the software is uploaded and started, the indicator remains steady green.
Running status Green Blinking once every 2s (0.5 Hz) The system is running properly, the Ethernet connection is normal, and STAs are associated with the AP.
Blinking once every 5s (0.2 Hz) The system is running properly, the Ethernet connection is normal, and no STA is associated with the AP. The system is in low power consumption state.
Alarm Green Blinking once every 0.25s (4 Hz) The software is being upgraded.
After the software is uploaded and started, the AP enters the registration state and has not registered successfully with the AC yet.
The AP registration fails (the CAPWAP link is disconnected).
Fault Red Steady on A fault that affects services has occurred, such as a DRAM detection failure or system software loading failure. The fault cannot be automatically rectified and must be rectified manually.

Highly reliable wireless access

  • Complies with IEEE 802.11a/b/g/n.
  • Supports 2 x 2 MIMO and provides a maximum rate of 300 Mbit/s.
  • Supports Wi-Fi Multimedia (WMM) and priority mapping on the air interface and wired interface.
  • Working on a single frequency and flexibly switches between the 2.4 GHz and 5 GHz frequency bands.
  • Supports wired link integrity check.
  • Supports roaming without service interruption.
  • Supports 11n beamforming.
  • Uses the latest 802.11n chip to provide higher performance and wider coverage.


Comprehensive user access control capability

  • Supports access control lists (ACLs) and implements user access control based on the user group policy.
  • Provides fine-grained bandwidth management for each user.
  • Supports user isolation policies.
  • Supports unified authentication on the AC.
  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address, user agent (UA) information in an HTTP packet, and DHCP options.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.


High security

  • Open system authentication
  • WEP authentication/encryption
  • WPA/WPA2-PSK authentication and encryption
  • WPA/WPA2-802.1x authentication and encryption
  • WAPI authentication and encryption
  • Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.


Flexible networking and environment adaptability

  • Has strong environment adaptability. The AP can automatically select the transmission rates, channels, and transmit power to adapt to various radio environments and avoid interference in real time.
  • Adjusts bandwidth allocation based on the user quantity and environment to improve user experience.
  • Identifies interference sources such as bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors in Fit AP mode and works with eSight to locate interference sources and display spectrums.


Simple device management and maintenance

  • Automatically goes online and loads the configuration, and supports plug-and-play (PnP).
  • Supports batch upgrade.
  • Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location.
  • Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology.

WLAN features

  • Complies with IEEE 802.11a/b/g/n.
  • Provides a maximum rate of 300 Mbit/s.
  • Maximum ratio combining (MRC).
  • Maximum-likelihood detection (MLD).
  • Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only).
  • Supports 802.11 dynamic frequency selection (DFS).
  • Short GI in 20 MHz and 40 MHz modes.
  • Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding.
  • Automatic and manual rate adjustment (the rate is adjusted automatically by default).
  • WLAN channel management and channel rate adjustment.
  • Automatic channel scanning and interference avoidance.
  • Service set identifier (SSID) hiding.
  • Signal sustain technology (SST).
  • Unscheduled automatic power save delivery (U-APSD).
  • Control and Provisioning of Wireless Access Points (CAPWAP).
  • Automatic login.


Network features

  • Compliance with IEEE 802.3u.
  • Auto-negotiation of the rate and duplex mode and automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X).
  • SSID-based VLAN assignment.
  • VLAN trunk on uplink Ethernet ports.
  • 4094 VLAN IDs (1-4094) and a maximum of 8 virtual APs (VAPs) for each radio.
  • AP control channel in tagged and untagged mode.
  • DHCP client, obtaining IP addresses through DHCP.
  • Tunnel data forwarding and direct data forwarding.
  • STA isolation in the same VLAN.
  • Access control lists (ACLs).
  • Link Layer Discovery Protocol (LLDP).
  • Uninterrupted service forwarding upon CAPWAP channel disconnection.
  • Unified authentication on the AC.
  • AC dual-link backup and VRRP hot backup.
  • Native IPv6
  • IPv4/IPv6 dual stack
  • IPv6 Portal
  • IPv6 SAVI
  • IPv4/IPv6 ACL


QoS features

  • Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding.
  • WMM parameter management for each radio.
  • WMM power saving.
  • Priority mapping for upstream packets and flow-based mapping for downstream packets
  • Queue mapping and scheduling.
  • User-based bandwidth limiting.
  • Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience).


Security features

  • Open system authentication.
  • WEP authentication/encryption.
  • WPA/WPA2-PSK authentication and encryption.
  • WPA/WPA2-802.1x authentication and encryption.
  • WAPI authentication and encryption.
  • Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist.
  • DHCP Snooping
  • DAI(Dynamic ARP Inspection)
  • IPSG(IP Source Guard)


Maintenance features

  • Unified management and maintenance on the AC.
  • Automatic login and configuration loading, and plug-and-play (PnP).
  • Batch upgrade.
  • Local AP management using Telnet.
  • Real-time configuration monitoring and fast fault location using the NMS.
  • System status alarm.


BYOD

  • Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address.
  • Identifies the device type according to the user agent (UA) information in an HTTP packet.
  • Identifies the device type according to DHCP options.
  • The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets.


Spectrum Analysis

  • Identifies interference sources such as bluetooth devices, microwave ovens, cordless phones, ZigBees, game controllers, 2.4 GHz/5 GHz wireless video and audio devices, and baby monitors.
  • Works with eSight to locate and perform spectrum analysis on interference sources.

Specifications

Item Description

Technical specifications

Dimensions (H×W×D) 45 mm x 86 mm x 86 mm
Weight ≤0.2 kg
System memory 128 MB

Power specifications

Power input PoE power: PoE function in compliance with IEEE 802.3af and 802.3at
Maximum power consumption 5.5 W
NOTE: The maximum power consumption depends on local laws.

Environment parameters

Operating temperature 0°C to +40°C
Storage temperature -40℃ to +70℃
Humidity 5% to 95% (non-condensing)
Altitude –60 m to 4000 m
Atmospheric pressure 70 kPa to 106kPa


Radio Specifications

Item Description
Antenna type Built-in antenna
Antenna gain 2.4 GHz: 2 dBi 5 GHz: 2.5 dBi
Maximum number of concurrent users ≤128
Maximum transmit power for each radio 2.4 GHz: 16 dBm
5 GHz: 14 dBm
NOTE
The actual transmit power depends on local laws and regulations. The AP2010DN uses a 86-type box and applies only to countries and regions that support 86-type boxes.
You can adjust the transmit power from the maximum transmit power to 1 dBm, with a step of 1 dB.
Maximum number of non-overlapping channels 2.4 GHz
802.11b/g
20 MHz: 3
802.11n
20 MHz: 3
40 MHz: 1
5 GHz
802.11a
20MHz: 5
802.11n
20MHz: 5
40MHz: 2
NOTE
The table uses the number of non-overlapping channels supported by China as an example. The number of non-overlapping channels varies in different countries. For details, see the Country Code & Channels compliance status
Channel rate 802.11b: 1, 2, 5.5, and 11 Mbit/s
802.11a/g: 6, 9, 12, 18, 24, 36, 48, and 54 Mbit/s
802.11n: 6.5 to 300 Mbit/s
Receiver sensitivity 2.4 GHz
802.11b (CCK)
-89 dBm @ 1
Mb/s
-88 dBm @ 2 Mb/s
-88 dBm @ 5.5 Mb/s
-87 dBm @ 11 Mb/s
2.4 GHz
802.11g (non-HT20)
-88 dBm @ 6 Mb/s
-85 dBm @ 9 Mb/s
-85 dBm @ 12 Mb/s
-84 dBm @ 18 Mb/s
-81 dBm @ 24 Mb/s
-78 dBm @ 36 Mb/s
-74 dBm @ 48 Mb/s
-71 dBm @ 54 Mb/s
2.4 GHz
802.11n (HT20)
-88 dBm @ MCS0
-85 dBm @ MCS1
-84 dBm @ MCS2
-81 dBm @ MCS3
-77 dBm @ MCS4
-74 dBm @ MCS5
-72 dBm @ MCS6
-69 dBm @ MCS7
2.4 GHz
802.11n(HT40)
-88 dBm @ MCS0
-84 dBm @ MCS1
-82 dBm @ MCS2
-77 dBm @ MCS3
-74 dBm @ MCS4
-71 dBm @ MCS5
-70 dBm @ MCS6
-69 dBm @ MCS7
5 GHz
802.11a (non-HT20)
-88 dBm @ 6 Mb/s
-87 dBm @ 9 Mb/s
-86 dBm @ 12 Mb/s
-83 dBm @ 18 Mb/s
-80 dBm @ 24 Mb/s
-77 dBm @ 36 Mb/s
-72 dBm @ 48 Mb/s
-71 dBm @ 54 Mb/s
5 GHz
802.11n (HT20)
-88 dBm @ MCS0
-85 dBm @ MCS1
-83 dBm @ MCS2
-78 dBm @ MCS3
-75 dBm @ MCS4
-71 dBm @ MCS5
-70 dBm @ MCS6
-69 dBm @ MCS7
5 GHz
802.11n (HT40)
-87 dBm @ MCS0
-84 dBm @ MCS1
-81 dBm @ MCS2
-78 dBm @ MCS3
-74 dBm @ MCS4
-71 dBm @ MCS5
-69 dBm @ MCS6
-68 dBm @ MCS7
-

The AP2010DN support 2.4GHz & 5GHz, and can flexibly switch between the 2 GHz and 5 GHz frequency bands as required. Complies with IEEE 802.11a/b/g/n.


Huawei AP2010DN designed for enterprises uses an 86 mm plate in compliance with international standards and can be easily installed in an 86-type box. It is beautifully designed, with a built-in antenna, a hidden indicator, and a sliding panel. The AP2010DN provides comprehensive service support capabilities and features high security, simple network deployment, automatic AC discovery and configuration, and real-time management and maintenance.


It provides wired and wireless connections, as well as phone connections, applicable to hotels, apartments, and office buildings.


Fit AP typical networking:

In this networking, the AP functions as a fit AP. The AC is responsible for user access, AP go-online, AP management, authentication, routing, security, and QoS.


Technology Topics


Related Products

Case Studies

DOCUMENTATION CENTER NEWS ROOM CASE STUDIES VIDEO ZONE PUBLICATIONS SHARE